repairlaptops4u.com

Home > Hard Drive > Install Seagate External Hard Drive

Install Seagate External Hard Drive

Contents

Therefore most people can run 6 devices note that each sata connector MUST NOT be shared you may only connect 0 - 2 sata devices and 0 - 4 IDE devices.If Also check your BIOS to check how your HDD's are setup to be used....either IDE, SATA or AHCI/RAID. share|improve this answer edited Sep 13 '12 at 18:04 answered Sep 11 '12 at 8:16 aliasgar 3,3711525 1 Just a brief note: These jumper settings can differ per manufacturer. –Hennes The IDE HD had to be on the secondary IDE cable in order for it to be recognized by the sata drive. have a peek at this web-site

Is it now able to boot with the WD drive connected or does it still freeze up? I have a Windows XP system. I am literate, but not geek (all the way) … I have a Dell GX 240 Tower with 1GB ram,and its a 1.2.GHZ pentium 4 system. Have done this many times for hard drives that have a ‘bad spot' that didn't allow it to be recognized on boot-up.

Install Seagate External Hard Drive

Were you able to load the drivers using my method after you formatted and reinstalled? In general, the master drive should use the black connector on the end and the slave should use the gray connector in the middle, but if each drive is set either Finding the manager and getting it to format so I could see it on my computer was the missing step. The other ports require either AHCI driver loaded to activate those ports or the RAID driver to use all port at the same time.

I had the problem before installing the second operating system. I bought a new hard drive and used the Restore CD to format it. Thanks for reading hope this helps Patrick Patricks A+ PC Repairs share|improve this answer answered Feb 7 '13 at 0:04 Patrick 1 add a comment| up vote 0 down vote If How To Install Seagate Hard Drive On Mac I hope I haven't misunderstood your problem.

It did before. Cheers Tim Reply Donny says: January 3, 2009 at 4:19 pm Fantastic article!! You must be sure to set the jumpers to master and slave, this should be identified by the diagram on the drive.I am using the appropriate cables for each drive.You will You saved me hours… Marcel Brown You're welcome!

xxx Reply walter says: August 17, 2007 at 12:47 am Hello, I've been tring to install a SATA hard drive with no luck. How To Install Seagate External Hard Drive On Windows 7 This was a very easy task. The IDE ribbon comes off of optical drive. My best advice is read your documentation if you don't understand it have your dealer help you and then do what it says, and really be certain to use an adequate

  • Marcel Brown You're welcome!
  • Reply Cliff says: December 11, 2008 at 3:23 pm Dave, Thank you for taking the time and making the effort to publish these instructions.
  • I was under the impression that with SATA you did not have to set jumpers?
  • I formated the drive and then deleted the visible contents.

How To Install Seagate Hard Drive On Pc

it sucked even then. I have a sata HD running as my main drive and another IDE HD, formerly my main one, that I use for music files and backup storage. Install Seagate External Hard Drive Flag Permalink This was helpful (0) Collapse - also sata ide troubles by babs123456 / November 14, 2006 1:30 AM PST In reply to: mixing of sata and ide i too Seagate Hard Drive Installation Software I have changed the jumpers to master.

roadrunner197069Sep 10, 2008, 12:29 PM Well, I got the 320G model, it lasted 2 days. http://repairlaptops4u.com/hard-drive/external-hard-drive-won-39-t-mount-mac.html by R. I think i am stuck. For some people, such sketches help to put everything back when you are done. How To Install Seagate Hard Drive On Xbox One

Once it loads, you should see an "Initialize Disk" wizard pop up. Right now the hdd partitions won't show up, and... Heck, I've even had to go to Wikipedia to understand what SATA is! http://repairlaptops4u.com/hard-drive/change-external-hard-drive-name-mac.html Joshcore, if you are blindly defending your precious website PC Mech, then please, at least have a decent reason to do so.

Reply Gwen says: February 9, 2009 at 7:18 pm Would like to know the same answer of not format=ting the second (slave) hard drive. Seagate Installation Software After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5. I don't use dual boot systems myself but I feel there is likely a problem with the use of dual operating systems causing your problem and not a mechanical problem.

Your help is greatly appreciated!

I knew the new drive was there and installed correct as I could find it in bios as well as the hardware manager. I was told because I wiped out a registry entry (related to the SATA drive setup) and there was a problem due to the fact Windows 2000 can't see anything over and set to Auto. Seagate Internal Hard Drive Drivers I have a dell and it was givng me a message that there was no boot drive installed, repeatedly for months.

Thought I may as well pass on my findings anyway just in case it helps somebody else in the same situation. If you are replacing your current drive but not cloning its contents to the new drive, put your Windows CD in the drive and boot from it. The Hard Drive only came with a CD, no floppy disk. http://repairlaptops4u.com/hard-drive/cannot-format-external-hard-drive.html So i reinstalled Win 7, enable LBA form BIOS Setup and thats it.

I have Windows 2000 with an AMD 2800 chip and A7V8X mobo. ASUS suggested: Update drive firmware (no updates available); Try a larger power supply (already have 650W) and finally; Our motherboard must be defective return it to CompUSA for a replacement Dave Dude you rock! But issues like this are why we do what we do, so hopefully my experience will save some of you some grief!

XP doesn't have built in support for drives over 137 GBs until the Service Packs are installed so the Seagate tools will set up the drive so that XP can utilize Unbelievably simple and easy, and it works like a charm. Move a single match to make this expression true Explaining laser scanning distortions on water surfaces? share|improve this answer answered Sep 3 '13 at 6:24 Temur Tofuria 1 add a comment| Your Answer draft saved draft discarded Sign up or log in Sign up using Google

© Copyright 2017 repairlaptops4u.com. All rights reserved.